View MAX2163ETI_6732889.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

max2163 isdb-t 1-segment tuner ________________________________________________________________ maxim integrated products 1 19-3104; rev 2; 10/09 for pricing, delivery, and ordering information, please contact maxim direct at 1-888-629-4642, or visit maxim? website at www.maxim-ic.com. evaluation kit available general description the max2163 low-if tuner ic is designed for use in 1-segment isdb-t applications. the max2163 directly converts uhf band signals to a low-if using a broad- band i/q downconverter. the operating frequency range covers the uhf band from 470mhz to 806mhz. the max2163 includes lnas, rf variable gain ampli- fiers, i and q downconverting mixers, a baseband vari- able gain amplifier, and a low-if filter. the max2163? variable gain amplifiers provide in excess of 100db of control range. the max2163 also includes fully monolithic vcos as well as a complete frequency synthesizer including an on-chip crystal oscillator and output buffer. the device operates with a crystal from 32mhz to 36mhz. the max2163 features a 2-wire i 2 c-compatible serial- control interface. a low-power standby mode is avail- able that shuts down the signal path leaving the control interface and register circuits active. additionally, an external pin can shut down the entire device. the max2163 is specified for operation in the extended -40? to +85? temperature range and is available in a 5mm x 5mm x 0.8mm, 28-pin thin qfn, lead-free plastic package with exposed paddle (ep). applications cell phone mobile tv personal digital assistants (pdas) game consoles portable tv devices portable audio devices automotive home audio features frequency range uhf: 470mhz to 806mhz (uhfin) low noise figure: 3.2db (typ) high dynamic range: -99dbm to 0dbm optional uhf tracking filter integrated vco and frequency synthesizer low lo phase noise: -87dbc/hz at 10khz integrated variable bw low-if filters greater than 40db image rejection single +2.4v to +3.47v supply low power: 80mw (typ) at +2.5v 2-wire i 2 c serial-control interface low-power shutdown and standby modes top view max2163 28 27 26 25 24 23 22 8 9 10 11 12 13 14 1 2 3 4 5 6 7 21 20 19 18 17 16 15 v ccvco ldo vtune gndsyn cpout v ccsyn xtalout n.c. n.c. n.c. gc1 v ccif gc2 v ccbias stby shdn lextu n.c. v cclna v ccrf uhfin xtal mux v ccdig sda + scl pwrdet ifout tank div2 div pwrdet frequency synthesizer interface logic and control pwrdet lextu pin configuration/ functional diagram typical application circuit appears at end of data sheet. ordering information part temp range pin- package MAX2163ETI+ -40c to +85c 28 tqfn-ep* MAX2163ETI/v+ -40c to +85c 28 tqfn-ep* + denotes a lead(pb)-free/rohs-compliant package. * ep = exposed pad. / v denotes an automotive qualified part. tqfn actual size (5mm x 5mm x 0.8mm)
max2163 isdb-t 1-segment tuner 2 _______________________________________________________________________________________ absolute maximum ratings dc electrical characteristics (max2163 evaluation kit, v cc = +2.4v to +3.47v, v gc1 = v gc2 = 0.3v (maximum gain), no rf input signal at uhfin. ifout is open cir- cuited and the vco is active with f lo = 557.714mhz, default register settings, t a = -40? to +85?, unless otherwise noted. typical val- ues are at v cc = +2.5v, t a =+25?, unless otherwise noted.) (note 1) stresses beyond those listed under ?bsolute maximum ratings?may cause permanent damage to the device. these are stress rating s only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specificatio ns is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. all v cc_ pins to gnd.............................................-0.3v to +3.6v uhfin to gnd.......................................................-0.3v to +0.9v ifout to gnd ............................................-0.3v to (v cc + 0.3v) gc1, gc2, vtune, xtalout, xtal to gnd ..........................................-0.3v to (v cc + 0.3v) cpout, xtlout, pwrdet to gnd ..........-0.3v to (v cc + 0.3v) sda, scl, shdn , stby to gnd...............-0.3v to (v cc + 0.3v) mux, lextu, ldo to gnd ........................-0.3v to (v cc + 0.3v) maximum rf input signal uhfin...................................+10dbm short-circuit duration ifout, cpout, xtalout, pwrdet, sda, mux ..........................................................10s continuous power dissipation (t a = +70?) 28-pin thin qfn (derate 34.5mw/? above +70?)....2758mw operating temperature range ...........................-40? to +85? junction temperature ......................................................+150? storage temperature range .............................-65? to +150? lead temperature (soldering, 10s) .................................+300? parameter conditions min typ max units supply voltage and supply current supply voltage 2.4 2.5 3.47 v supply current normal mode 30.4 40 ma supply current high-linearity mode rfvga = 1; mxr = 1 35 44 ma supply current hw or sw standby mode 1.1 2.0 ma supply current shutdown mode 1 20 a analog gain-control inputs (gc1, gc2) voltage range maximum gain = 0.3v 0.3 2.1 v input bias current -15 +15 a power detector output buffer (pwrdet) output voltage range load impedance = 2k ||10pf 0.3 2.1 v output impedance 25 vco tuning voltage input (vtune) voltage range 0.35 2.05 v digital controls ( shdn , stby) input logic-level high 0.7 x v cc v input logic-level low 0.3 x v cc v 2-wire serial i 2 c digital inputs (scl, sda) clock frequency 400 khz input logic-level high 0.7 x v cc v input logic-level low 0.3 x v cc v caution! esd sensitive device
max2163 isdb-t 1-segment tuner _______________________________________________________________________________________ 3 dc electrical characteristics (continued) (max2163 evaluation kit, v cc = +2.4v to +3.47v, v gc1 = v gc2 = 0.3v (maximum gain), no rf input signal at uhfin. ifout is open cir- cuited and the vco is active with f lo = 557.714mhz, default register settings, t a = -40? to +85?, unless otherwise noted. typical val- ues are at v cc = +2.5v, t a =+25?, unless otherwise noted.) (note 1) parameter conditions min typ max units 2-wire serial i 2 c digital output (sda) output logic-level low 0.4 v mux digital output output logic-level low 0.3 x v cc v output logic-level high 0.7 x v cc v ac electrical characteristics (max2163 evaluation kit, v cc = +2.4v to +3.47v, f rf = 557.143mhz, f lo = 557.714mhz, f if = 571khz, f xtal = 36mhz, v gc1 = v gc2 = 0.3v (maximum gain), default register settings, rf input signals as specified, if output load as specified, t a = -40? to +85?, unless otherwise noted. typical values are at v cc = +2.5v, t a = +25?, shdn = v cc , stby = gnd, unless otherwise noted.) (note 1) parameter conditions min typ max units main signal path performance receive input frequency range uhfin (note 2) 470 806 mhz maximum voltage gain -100dbm cw tone, v gc1 = v gc2 = 0.3v v ifout = 0.225v p-p 96 db minimum voltage gain 0dbm cw tone, v gc1 = v gc2 = 2.1v v ifout = 0.1v p-p -2 db rf gain control range (gc1) 40 52 db analog if gain control range (gc2) 60 76 db in-band im3 (note 3) -40 dbc out-of-band iip3 (note 4) 30 dbm input p 1db in-band cw tone, v gc1 = v gc2 = 2.1v 0 dbm image rejection t a = +25 c, +85c 40 49 db noise figure t a = +25 c, 470mhz < f rf < 806mhz 3.2 5.3 db optional uhf tracking filter center frequency 640 mhz nominal 3db bandwidth lextu = 18nh, q min = 35 320 mhz wideband rf overload detector typical rf attack point relative to rfagc attack point +28 db
max2163 isdb-t 1-segment tuner 4 _______________________________________________________________________________________ ac electrical characteristics (continued) (max2163 evaluation kit, v cc = +2.4v to +3.47v, f rf = 557.143mhz, f lo = 557.714mhz, f if = 571khz, f xtal = 36mhz, v gc1 = v gc2 = 0.3v (maximum gain), default register settings, rf input signals as specified, if output load as specified, t a = -40? to +85?, unless otherwise noted. typical values are at v cc = +2.5v, t a = +25?, shdn = v cc , stby = gnd, unless otherwise noted.) (note 1) parameter conditions min typ max units if power detector minimum attack point -66 dbm maximum attack point -52 dbm detector accuracy 1.5 db pdbw[1:0]=00 43 pdbw[1:0]=01 26 pdbw[1:0]=10 17 3db frequency response pdbw[1:0]=11 13 mhz low-if filter response center frequency 571 khz 219khz offset from center frequency -2.8 +2.8 1-segment mode frequency response 1mhz offset from center frequency -80 db low-if output characteristics nominal output-voltage swing r load = 10k ||10pf 225 mv p-p output impedance single-ended, real 31 frequency synthesizer n-divider frequency range 90 804 mhz n-divider range 256 4095 reference divider frequency range 32 36 mhz reference divider range (r) 112 280 phase detector comparison frequency 1/7 2/7 mhz pll referred phase noise floor f comp = 2/7mhz -153 dbc/hz spurious products f comp spurious -70 dbc cp bits = 00 1.0 1.5 2.0 cp bits = 01 1.4 2.0 2.6 cp bits = 10 1.8 2.5 3.3 charge-pump output current cp bits = 11 2.1 3.0 3.9 ma voltage-controlled oscillator and lo gen guaranteed vco frequency range 1890 3216 mhz guaranteed lo frequency range 472.5 804.0 mhz f offset = 1khz -82 f offset = 10khz -87 f offset = 100khz -108 f offset = 1mhz -128 lo phase noise f offset > 10mhz -140 dbc/hz
max2163 isdb-t 1-segment tuner _______________________________________________________________________________________ 5 ac electrical characteristics (continued) (max2163 evaluation kit, v cc = +2.4v to +3.47v, f rf = 557.143mhz, f lo = 557.714mhz, f if = 571khz, f xtal = 36mhz, v gc1 = v gc2 = 0.3v (maximum gain), default register settings, rf input signals as specified, if output load as specified, t a = -40? to +85?, unless otherwise noted. typical values are at v cc = +2.5v, t a = +25?, shdn = v cc , stby = gnd, unless otherwise noted.) (note 1) parameter conditions min typ max units crystal oscillator input (xtal) frequency range 32 36 mhz input capacitance crystal load capacitance 8 pf input overdrive level ac-coupled sine wave input 0.5 1.5 v p-p input negative resistance f xtal = 36mhz 575 reference oscillator buffer output (xtalout) output frequency range 16 18 mhz output voltage swing z l = 4k ||10pf 0.5 1.0 v p-p output buffer divide range 2 2 output duty cycle 45 55 % output turn-on time xtal amplitude > 0.5v p-p 4 ms note 1: min and max values are production tested at t a = +85?. min and max limits at t a = -40? and +25? are guaranteed by design and characterization. note 2: ifout output voltage level met over this range. note 3: in-band im3 is measured with two tones at f lo - 450khz and f lo - 550khz. the rfagc is engaged and set for the default attack point of -58dbm. ifl[1:0] = 01, rfvga = mxr = 1. v gc2 is adjusted to maintain 225mv p-p at if out . input power levels (tone 1 plus tone 2) up to -10dbm and > 30dbc for levels from -10dbm to 0dbm. note 4: v gc1 is set for maximum attenuation (2.1v) and v gc2 is adjusted to maintain 225mv p-p at i fout for an equivalent 0dbm input desired level. closed loop, attack point at -58dbm, f rf = 767.143mhz, f lo = 767.714mhz, f rf1 = f rf + 4.25mhz, f rf2 = f rf + 8mhz, -10dbm/tone. rfgr = 1, rfvga = 1, and mxr = 1.
max2163 isdb-t 1-segment tuner 6 _______________________________________________________________________________________ normal mode supply current vs. supply voltage max2163 toc01 supply voltage (v) supply current (ma) 30.5 30.0 31.0 31.5 32.0 32.5 33.0 29.5 29.0 28.5 2.4 2.8 2.7 2.6 3.0 2.9 3.1 3.3 3.2 2.5 t a = +85 c t a = +25 c t a = -40 c uhf voltage gain vs. frequency max2163 toc02 frequency (mhz) uhf voltage gain (db) 102 106 110 100 104 108 470 670 570 520 820 720 770 620 relative uhf gain range vs. v gc1 max2163 toc03 v gc1 (v) relative vhf gc1 gain range (db) -30 -10 10 -40 -20 -60 -70 -50 0 0.30 1.10 0.70 0.50 2.10 1.30 1.50 1.90 1.70 0.90 relative if gain range vs. gc2 max2163 toc04 v gc2 (v) relative if gain range (db) -40 -20 0 -50 -30 -70 -80 -90 -100 -60 -10 0.30 0.90 1.50 2.10 0.60 1.20 1.80 typical operating characteristics (max2163 evaluation kit, v cc = +2.5v, default register settings, v gc1 = v cg2 = 0.3v, v ifout = 225mv p-p , f lo = 557.714mhz, t a = +25?, unless otherwise noted.) uhf v tune vs. lo frequency max2163 toc06 lo frequency (mhz) vco 0, sb0-15 vco 1, sb0-15 vco 2, sb0-15 v tune (v) 0.50 0 1.00 1.50 2.00 2.50 3.00 410 530 650 610 770 490 730 650 770 730 450 570 uhf noise figure vs. frequency max2163 toc05 frequency (mhz) uhf noise figure (db) 2.5 2.0 3.0 3.5 4.0 4.5 5.0 1.5 1.0 0.5 0 460 810 660 710 560 510 760 610 t a = +85 c t a = +25 c t a = -40 c uhf lo-to-rfin leakage vs. frequency max2163 toc07 frequency (mhz) lo-to-rfin leakage (dbm) -115 -109 -113 -103 -101 -105 -107 -111 460 510 610 710 810 560 660 760
max2163 isdb-t 1-segment tuner _______________________________________________________________________________________ 7 1-segment baseband filter frequency response max2163 toc08 frequency (khz) normalized gain (db) -70 -20 -40 10 0 -10 -30 -60 -50 0 2000 500 1000 1250 1750 250 1500 750 1-segment baseband filter frequency response max2163 to09 frequency (khz) normalized gain (db) -10 4 2 2 -4 10 8 6 0 -8 -6 0 1250 500 1000 250 750 1-segment group delay variation vs. baseband frequency max2163 toc10 frequency (khz) group delay variation ( s) -0.5 4.0 1.0 2.5 0 1.5 3.0 0.5 2.0 3.5 0 1200 800 400 1000 600 200 typical operating characteristics (continued) (max2163 e valuation kit, v cc = +2.5v, default register settings, v gc1 = v cg2 = 0.3v, v ifout = 225mv p-p , f lo = 557.714mhz, t a = +25?, unless otherwise noted.) phase noise vs. offset frequency max2163 toc11 offset frequency (khz) phase noise (dbc/hz) -150 -120 -100 -80 -60 -130 -140 -110 -90 -70 -50 1 10 100 1000 uhf xtal port input impedance vs. xtal frequency max2163 toc13 xtal frequency (mhz) input impedance, real component ( ? ) -7.00e+02 -5.50e+02 -6.00e+02 -6.50e+02 -7.50e+02 32 35 34 33 36 uhf input return loss vs. rf frequency max2163 toc12 810mhz 470mhz uhf input return loss uhf lo phase noise at 10khz offset vs. channel frequency max2163 toc14 channel frequency (mhz) uhf phase noise at 10khz offset (dbc/hz) -92 -80 -84 -86 -90 -82 -88 -78 450 600 750 500 650 800 550 700 850
max2163 isdb-t 1-segment tuner 8 _______________________________________________________________________________________ pin description pin name description 1 stby device standby. connect to logic-high to place the device in standby mode. connect to logic-low for normal operation. this pin is logically ored to the stby bit. 2 shdn device shutdown. connect to logic-low to place the device in shutdown mode. 3 lextu optional uhf tracking filter inductor. connect an 18nh inductor from this pin to ground. 4, 8, 9, 10 n.c. no connection. connect to the pcb ground plane. 5v cclna dc power supply for lna. connect to a +2.5v low-noise supply. bypass to gnd with a 0.1? capacitor placed as close as possible to the pin. do not share capacitor ground vias with other ground connections. 6v ccrf dc power supply for rf circuits. connect to a +2.5v low-noise supply. bypass to gnd with a 0.1? capacitor placed as close as possible to the pin. do not share capacitor ground vias with other ground connections. 7 uhfin uhf 50 ? rf input. incorporates an internal dc-blocking capacitor. 11 gc1 rf gain control input. in closed-loop rfagc mode (pdbm[1:0] = 11), connecting a capacitor from gc1 to ground sets the agc response time. in open-loop rfagc mode (pdbm[1:0] = 10), gc1 is a high-impedance analog input that controls the rfagc. 12 v ccif dc power supply for if circuits. connect to a +2.5v low-noise supply. bypass to gnd with a 0.1? capacitor placed as close as possible to the pin. do not share capacitor ground vias with other ground connections. 13 gc2 if gain control input. high-impedance analog input. 14 v ccbias dc power supply for bias circuits. connect to a +2.5v low-noise supply. bypass to gnd with a 0.1? capacitor placed as close as possible to the pin. do not share capacitor ground vias with other ground connections. 15 ifout low-if output. requires a dc-blocking capacitor. 16 pwrdet low-impedance power detector output buffer. bits pdbm[1:0] control the function of this output pin. see table 6. 17 scl 2-wire serial-clock interface. requires a pullup resistor to v ccdig . 18 sda 2-wire serial-data interface. requires a pullup resistor to v ccdig .
max2163 isdb-t 1-segment tuner _______________________________________________________________________________________ 9 pin name description 19 v ccdig dc power supply for digital logic circuits. connect to a +2.5v low-noise supply. bypass to gnd with a 0.1? capacitor placed as close as possible to the pin. do not share capacitor ground vias with other ground connections. 20 mux device test. see table 14 for details. 21 xtal base contact of internal colpitts oscillator. see the typical application circuit for details. 22 xtalout crystal oscillator buffer output. a dc-blocking capacitor must be used when driving external circuitry. 23 v ccsyn dc power supply for synthesizer circuits. connect to a +2.5v low-noise supply. bypass to gnd with a 0.1? capacitor placed as close as possible to the pin. do not share capacitor ground vias with other ground connections. 24 cpout charge-pump output. connect this output to the pll loop filter input with the shortest connection possible. 25 gndsyn synthesizer ground. connect to the pcb ground plane. do not share ground vias with other ground connections. 26 vtune high-impedance vco tune input. connect the pll loop filter output directly to this pin with as short as possible of a connection. 27 ldo internal ldo bypass. bypass to gnd with a 470nf capacitor placed as close as possible to the pin. do not share capacitor ground vias with other ground connections. 28 v ccvco dc power supply for vco circuits. connect to a +2.5v low-noise supply. bypass to gnd with a 0.1? capacitor placed as close as possible to the pin. do not share capacitor ground vias with other ground connections. ?p exposed paddle. solder evenly to the board? ground plane for proper rf performance and enhanced thermal dissipation. not intended as an electrical connection point. pin description (continued)
max2163 isdb-t 1-segment tuner 10 ______________________________________________________________________________________ detailed description register descriptions the max2163 includes 16 programmable registers and 2 read-only registers. note: all programmable registers must be written no earlier than 100? after device power- up or recovery from a brownout event (i.e., when v cc drops below 1v). follow up by rewriting the registers needed for channel/frequency programming (i.e., regis- ters 00?8) or simply rewrite all registers. the default val- ues listed in tables 1?5 are provided for informational purposes only. the user must write all required register values, including ?actory use only?values. msb data byte register number register name read/ write register address d7 d6 d5 d4 d3 d2 d1 d0 00 if filter read/ write 0x00 tun2 tun1 tun0 flts ifl1 ifl0 pdbw1 pdbw0 01 vas read/ write 0x01 1 vass vas cps adl ade ltc1 ltc0 02 vco read/ write 0x02 0 vco1 vco0 vsb3 vsb2 vsb1 vsb0 vcob 03 pdet/ rf-filt read/ write 0x03 pdbm1 pdbm0 pdet2 pdet1 pdet0 rflt2 rflt1 rflt0 04 mode read/ write 0x04 rfvb rffb hsls 0 0 0 0 0 05 r-divider msb read/ write 0x05 r8 r7 r6 r5 r4 r3 r2 r1 06 r-divider lsb/cp read/ write 0x06 cp1 cp0 0 drfd rfda1 rfda0 1 r0 07 n-divider msb read/ write 0x07 n11 n10 n9 n8 n7 n6 n5 n4 08 n-divider lsb/lin read/ write 0x08 n3 n2 n1 n0 0 mix rfvga stby 09 status read only 0x09 x x adc2 adc1 adc0 vcp1 vcp0 pwr 0a vas status read only 0x0a vvco1 vvco0 vvsb3 vvsb2 vvsb1 vvsb0 vasa vase 0bC11 factory use only read/ write 0x0bC 0x11 0 0 0 0 0 0 0 0 table 1. i 2 c and 4-wire register configuration
max2163 isdb-t 1-segment tuner ______________________________________________________________________________________ 11 i 2 c read/write addresses the max2163 i 2 c read/write addresses are c1/c0. see table 2 for details. device address address type d7 d6 d5 d4 d3 d2 d1 d0 c0 write 1 1 0 0 0 0 0 0 c1 read 1 1 0 0 0 0 0 1 table 2. max2163 i 2 c write addresses bit name bit location (0 = lsb) default function tun[2:0] 7, 6, 5 011 sets the if filter center frequency. this filters center frequency is trimmed at the factory, but can be manually adjusted by setting the flts bit and programming the tun[2:0] bits as follows: 000 - 0.75 x f if (not factory tested.) 001 - 0.84 x f if (not factory tested.) 010 - 0.92 x f if (not factory tested.) 011 - f if (571khz) 100 - 1.08 x f if (not factory tested.) 101 - 1.16 x f if (not factory tested.) 110 - 1.25 x f if (not factory tested.) 111 - 1.33 x f if (not factory tested.) flts 4 0 selects which registers set low-if bandpass filter center frequency and bandwidth. 0 = selects internal factory set register. 1 = selects manual trim register tun[2:0] (not factory tested). ifl[1:0] 3, 2 01 set the bias current for the low-if circuits to provide for fine linearity adjustments. program to 01 upon power-up. pdbw[1:0] 1, 0 11 sets the if power detector bandwidth. 00 = 43mhz bandwidth. 01 = 26mhz bandwidth. 10 = 17mhz bandwidth. 11 = 13mhz bandwidth. table 3. if filter register
max2163 isdb-t 1-segment tuner 12 ______________________________________________________________________________________ bit name bit location (0 = lsb) default function x 7 1 factory use only. must be programmed to 1 upon power-up. vass 6 0 controls the vco autoselect (vas) start conditions function. 0 = vas starts from the current vco/vcosb loaded in the vco[1:0] and vsb[3:0] registers. 1 = vas starts from the currently used vco and vcosb. vas 5 1 controls the vco autoselect (vas) function. 0 = disables the vco autoselect function and allows manual vco selection through the vco[1:0] and vsb[3:0] bits. 1 = enables the on-chip vco autoselect state machine. cps 4 1 sets the charge-pump current selection mode between automatic and manual. 0 = charge-pump current is set ma nually through the cp[1:0] bits. 1 = charge-pump current is automatically selected. also requires ade, adl, and vas bits to be programmed to 1. adl 3 0 enables or disables the vco tuning voltage adc latch. 0 = disables the adc latch. 1 = latches the adc value. ade 2 0 enables or disables vco tuning voltage adc. 0 = disables adc read. 1 = enables adc read. ltc[1:0] 1, 0 11 sets the vco autoselect wait time. 00 = 14336/f xtal . 01 = 24576/f xtal . 10 = 34816/f xtal . 11 = 45056/f xtal . table 4. vas register bit name bit location (0 = lsb) default function x 7 0 factory use only. must be programmed to 0 upon power-up. vco[1:0] 6, 5 01 controls which vco band is activated when using manual vco programming mode. this also serves as the starting point for vco autoselect mode when vass = 0. 00 = select vco-0. 01 = select vco-1. 10 = select vco-2. 11 = not used. table 5. vco register
max2163 isdb-t 1-segment tuner ______________________________________________________________________________________ 13 bit name bit location (0 = lsb) default function vsb[3:0] 4, 3, 2, 1 0100 select a particular sub-band for each of the on-chip vcos. together with the vco[1:0] bits a manual selection of a vco band and a sub-band can be made. this also serves as the starting point for the vco autoselect mode when vass = 0. 0000 = select sub-band 0. 0001 = select sub-band 1. 1111 = select sub-band 15. vcob 0 1 sets the vco bias mode. 0 = normal mode. 1 = low-power mode. table 5. vco register (continued) bit name bit location (0 = lsb) default function pdbm[1:0] 7, 6 00 power detector and buffer mode. 00 = p ow er d etector i s enab l ed , p w rd e t b uffer i s off. o n- chi p cl osed - l oop rfagc . 01 = power detector is enabled, pwrdet buffer is on with detector rms voltage output at pwrdet pin (rfagc is open loop with rf gain controlled by voltage applied to gc1). 10 = unused. 11 = power detector is enabled; pwrdet buffer is on with the gc1 voltage output at pwrdet pin (on-chip closed loop rfagc). pdet[2:0] 5, 4, 3 100 sets the agc attack point. 000 = -66dbm. 001 = -64dbm. 010 = -62dbm. 011 = -60dbm. 100 = -58dbm. 101 = -56dbm. 110 = -54dbm. 111 = -52dbm. rflt[2:0] 2, 1, 0 011 sets the center frequency of the uhf tracking filter when used. 000 = minimum frequency (see table 17). ------------ 111 = maximum frequency (see table 17). table 6. pdet/rf-filt register
max2163 isdb-t 1-segment tuner 14 ______________________________________________________________________________________ bit name bit location (0 = lsb) default function cp[1:0] 7, 6 00 sets the charge-pump current. 00 = 1.5ma. 01 = 2ma. 10 = 2.5ma. 11 = 3ma. x 5 0 factory use only. must be programmed to 0 upon power-up. drfd 4 1 disable rf detector 0 = enables the wideband rf overload detector. 1 = disables the wideband rf overload detector. rfda[1:0] 3, 2 11 sets the rf overload detector attack point (subtract 6db to each if pdiq = 0). 00 = +37db relative to if attack point setting. 01 = +34db relative to if attack point setting. 10 = +31db relative to if attack point setting. 11* = +28db relative to if attack point setting. * only 11 is factory tested. x 1 1 factory use only. must be programmed to 1 upon power-up. r0 0 0 lsb of reference divider number table 9. r-divider lsb/cp register note: when changing r-divider value, both registers r-divider msb and r-divider lsb must be loaded as they are double buffered. bit name bit location (0 = lsb) default function rfvb 7 0 bypass 3rd-stage rfvga. 0 = enables 3rd-stage rfvga. 1 = disables the 3rd-stage rfvga. rffb 6 0 bypass integrated rf filter. 0 = enables optional rf filter. 1 = disables optional rf filter. hsls 5 0 selects between high-side and low-side lo injection. 1 = low-side injection. 0 = high-side injection. x 4, 3, 2, 1, 0 0 factory use only. must be programmed to 0 upon power-up. table 7. mode register bit name bit location (0 = lsb) default function r[8:1] 7, 6, 5, 4, 3, 2, 1, 0 00111111 sets the pll reference divider (r) number. default r divide value is 126 decimal. r can range from 16 to 511 decimal. table 8. r-divider msb register note: when changing r-divider value, both registers r-divider msb and r-divider lsb must be loaded as they are double buffered.
max2163 isdb-t 1-segment tuner ______________________________________________________________________________________ 15 bit name bit location (0 = lsb) default function n[11:4] 7, 6, 5, 4, 3, 2, 1, 0 01111010 sets the most significant bits of the pll integer divide number (n). default integer divider value is n = 1952 decimal. n can range from 1314 to 2687. table 10. n-divider msb register bit name bit location (0 = lsb) default function n[3:0] 7, 6, 5, 4 0000 sets the least significant bits of the pll integer divide number (n). default integer divider value is n = 1952 decimal. n can range from 1314 to 2687. x 3 0 factory use only. must be programmed to 0 upon power-up. mix 2 0 sets linearity mode of mixers. 0 = selects normal mode for mixer. 1 = selects high linearity mode for mixer. rfvga 1 0 sets linearity mode of 3rd-stage rfvga. 0 = selects normal mode for 3rd-stage rfvga. 1 = selects high linearity mode for 3rd-stage rfvga. stby 0 0 selects standby mode when stby pin is logic-low. 0 = normal operation. 1 = disables the signal path and frequency synthesizer leaving only the serial bus, crystal oscillator, and xtalout buffer active. table 11. n-divider lsb/lin register note: when changing n-divider value, both registers n-divider msb and n-divider lsb must be loaded as they are double buffered. note: when changing n-divider value, both registers n-divider msb and n-divider lsb must be loaded as they are double buffered.
max2163 isdb-t 1-segment tuner 16 ______________________________________________________________________________________ bit name bit location (0 = lsb) default function x 7, 6, 5, 4, 3, 2, 1, 0 00000000 factory use only. must be programmed to 0 upon power-up. table 14. factory use only registers (0b, 0c, 0d, 0e, 0f, 10 and 11) bit name bit location (0 = lsb) default function x 7, 6 1,1 unused adc[2:0] 5, 4, 3 indicates the 3-bit adc conversion of the vco tuning voltage (vtune). vcp[1:0] 2, 1 reflects the charge-pump current setting, when cps = 1. pwr 0 1 logic-high indicates power has been cycled. status register read operation resets pwr to 0. table 12. status register (read only) bit name bit location (0 = lsb) default function vvco[1:0] 7, 6 indicates which vco has been selected by the vco autoselect state machine. see table 5 for vco[1:0] definition. vvsb[3:0] 5, 4, 3, 2 indicates which sub-band of a particular vco has been selected by either the vco autoselect state machine. see table 5 for vsb[2:0] definition. vasa 1 indicates whether vco autoselection was successful. 0 = indicates the autoselect function is disabled or unsuccessful vco selection. 1 = indicates successful vco autoselection. vase 0 status indicator for the vco autoselect function. 0 = indicates the vco autoselect function is active. 1 = indicates the vco autoselect function is inactive. table 13. vas status register (read only)
max2163 isdb-t 1-segment tuner ______________________________________________________________________________________ 17 pin and bit truth tables the max2163 stby can be controlled by either a hard- ware pin or a register bit. the truth table for each is described in table 15. for software control of the stby mode, connect the stby pin to ground. normal and high-linearity mode definitions table 16 defines the register setup for normal and high- linearity modes. 2-wire serial interface the max2163 features a 2-wire i 2 c-compatible serial interface consisting of a serial-data line (sda) and a serial-clock line (scl). sda and scl facilitate bidirec- tional commun ication between the max2163 and the master at clock frequencies up to 400khz. the master device initiates a data transfer on the bus and generates the scl signal to permit data transfer. the max2163 functions as an i 2 c slave device that transfers and receives data to and from the master. pull sda and scl high with external pullup resistors of 1k ? or greater refer- enced to max2163 v ccdig for proper i 2 c operation. one bit transfers during each scl clock cycle. a mini- mum of nine clock cycles is required to transfer a byte into or out of the max2163 (8 bits and an ack/nack). the data on sda must remain stable during the high period of the scl clock pulse. changes in sda while scl is high and stable are considered control signals (see the start and stop conditions section). both sda and scl remain high when the bus is not busy. start and stop conditions the master initiates a transmission with a start condi- tion (s), which is a high-to-low transition on sda while scl is high. the master terminates a transmission with a stop condition (p), which is a low-to-high transition on sda while scl is high. acknowledge and not-acknowledge conditions data transfers are framed with an acknowledge bit (ack) or a not-acknowledge bit (nack). both the mas- ter and the max2163 (slave) generate acknowledge bits. to generate an acknowledge, the receiving device must pull sda low before the rising edge of the acknowledge-related clock pulse (ninth pulse) and keep it low during the high period of the clock pulse. to generate a not-acknowledge condition, the receiver allows sda to be pulled high before the rising edge of the acknowledge-related clock pulse, and leaves sda high during the high period of the clock pulse. monitoring the acknowledge bits allows for detection of unsuccessful data transfers. an unsuccessful data transfer happens if a receiving device is busy or if a system fault has occurred. in the event of an unsuc- cessful data transfer, the bus master must reattempt communication at a later time. stby pin stby bit device state vcc 0 device in standby mode vcc 1 device in standby mode gnd 0 device in normal mode gnd 1 device in standby mode table 15. standby bit truth table bit normal mode high linearity mode rfvga 0 1 mix 0 1 table 16. register setup for normal and high-linearity modes
max2163 isdb-t 1-segment tuner 18 ______________________________________________________________________________________ slave address the max2163 has a 7-bit i 2 c slave address that must be sent to the device following a start condition to ini- tiate communication. the slave address is internally programmed to c0 or c2 for write and c1 or c3 for read. see table 2. the max2163 continuously awaits a start condition followed by its slave address. when the device recog- nizes its slave address, it acknowledges by pulling the sda line low for one clock period; it is ready to accept or send data depending on the r/ w bit (figure 1). write cycle when addressed with a write command, the max2163 allows the master to write to a single register or to multi- ple successive registers. a write cycle begins with the bus master issuing a start condition followed by the 7 slave address bits and a write bit (r/ w = 0). the max2163 issues an ack if the slave address byte is successfully received. the bus master must then send the address of the first reg- ister it wishes to write to (see table 1 for register addresses). the slave acknowledges the address, and the master can then write one byte to the register at the specified address. data is written beginning with the most significant bit (msb). the max2163 again issues an ack if the data is successfully written to the register. the master can continue to write data to the successive internal registers with the max2163 acknowledging each successful transfer, or the master can terminate transmission by issuing a stop condition. the write cycle does not terminate until the master issues a stop condition. figure 2 illustrates an example in which registers 0 through 2 are written with 0x0e, 0x08, and 0xe1, respectively. read cycle when addressed with a read command, the max2163 allows the master to read back a single register or mul- tiple successive registers. a read cycle begins with the bus master issuing a start condition followed by the 7 slave address bits and a write bit (r/ w = 0). the max2163 issues an ack if the slave address byte is successfully received. the bus master must then send the address of the first register it wishes to read (see table 1 for register addresses). the slave acknowledges the address. then a start condi- tion is issued by the master, followed by the 7 slave address bits and a read bit (r/ w = 1). the max2163 issues an ack if the slave address byte is successfully received. the max2163 starts sending data msb first with each scl clock cycle. at the 9th clock cycle, the master can issue an ack and continue to read succes- sive registers, or the master can terminate the transmis- sion by issuing a nack. the read cycle does not terminate until the master issues a stop condition. figure 3 illustrates an example in which registers 0 through 2 are read back. 3 sdr scl 1 123456789 100 01 slave address 0 rival ack figure 1. max2163 slave address byte write data to register 0x00 write data to register 0x01 write data to register 0x02 write register address write 0b/ce address 0x0e 0x0e 0xe1 stop start 0x00 1100000 0 ? ? ? ? ? ack ack ack r/w ack ack figure 2. write register 0 through 2 with 0x0e, 0x08, and 0xe1, respectively.
max2163 isdb-t 1-segment tuner ______________________________________________________________________________________ 19 applications information rf input (uhfin) the max2163 uhfin input is internally matched to 50 ? . rf gain control (gc1) the max2163 features multistage rf variable gain amplifiers controlled by pin gc1 that provide in excess of 54db typical of rf gain control range. the voltage control range is 0.3v at maximum gain to 2.1v at mini- mum gain. the rf gain control can be configured for open-loop control or for closed-loop rf automatic gain control (agc) when combined with the on-chip if power detector. to set the response time of the agc, connect a capacitor from gc1 to ground. see the closed-loop rf gain control section for more information. optional rf tracking filter the max2163 features an optional rf tracking filter at the output of the 3rd-stage rfvga. this filter is con- trolled by the rflt bits as shown in the mode register. see table 7. to enable the filter, set rffb bit to 0; to disable filter, set rffb bit to 1. see table 17 for proper center frequency settings. in the event that the rf track- ing filter is not used, do not install the 18nh inductor. rf overload detector the max2163 includes an rf overload detector. the rf overload detector circuit is enabled or disabled with the drfd bit as shown in table 10 (r-divider lsb/cp register). if gain control (gc2) the max2163 features an if variable gain amplifier that provides in excess of 65db of if gain control range. the voltage control vgc2 range is 0.3v at maximum gain to 2.1v at minimum gain. the if vga is controlled by the channel decoder. if power detector the max2163 features a true rms if power detector at the mixer output with adjustable bandwidth. the power detector circuit is enabled or disabled with the pdbm[1:0] bits in the pdet/rf-filt register (table 6). the attack point can be set through the pdet[2:0] bits in the pdet/rf-filt register (see table 6 for a summa- ry of attack-point settings). the pwrdet pin can be configured to provide a low- impedance buffered and scaled version of either the gc1 voltage when using the on-chip closed loop agc, or the if power detectors rms voltage for use in off-chip closed loop agc schemes. the output voltage at this pin ranges from 0.3v to 2.1v, with 2.1v indicating the maxi- mum rf input power. this output allows the baseband processor to monitor the received rf power level. when using the on-chip closed-loop agc function (pdbm = 11), the pwrdet buffer provides a low- impedance buffered version of the gc1 voltage. this out- put can be monitored by the demodulator lsi to determine the state of the rf front-end and subsequently used to control other circuits (external lna) or various demodula- tor functions. the pwrdet output can also be disabled for reduced overall power consumption (pdbm = 00). for use in off-chip closed-loop agc schemes, the pwrdet buffer output can be configured to provide a low-impedance scaled version of the if power detec- tors rms voltage (pdbm = 10). in this mode, an exter- nal voltage is applied to the gc1 pin to close the loop. device address reg 00 data reg 01 data reg 02 data register address device address 1100000 1100000 0 1 xxxxxxxx xxxxxxxx xxxxxxxx s t o p n a c k s t a r t s t a r t 00000000 a c k a c k a c k r/w r/w a c k a c k figure 3. receive data from read registers rflt uhf (mhz) 000 470C488 001 488C512 010 512C542 011 542C572 100 572C608 101 608C656 110 656C710 111 710C806 table 17. rflt[2:0] center frequency settings
closed-loop rf gain control the max2163 can provide either open-loop rf gain control by the gc1 pin or closed-loop rf automatic gain control (agc) by the on-chip power detector. automatic rf gain control is enabled by setting the pdbm[1:0] bits to 00 as shown in the pdet/rf-filt register (table 6). setting the pdbm[1:0] bits to 10 allows open-loop rf gain control by the gc1 pin. when the rf agc loop is disabled, rf gain is con- trolled by an external voltage that is applied to the gc1 pin. the gc1 pin? input voltage range is 0.3v to 2.1v with 0.3v providing the maximum rf gain. when the rf agc loop is enabled, the if power detec- tor output is internally connected to the gc1 input and the rf gain is controlled by the power detector? output voltage. an external capacitor connected from the gc1 pin to ground sets the agc loop response time. the loop response time is calculated as follows: t settling = 41.7 x r x c ext where: r = 1k ? c ext = external capacitor from gc1 to ground in farads. the attack point (referred to as the rf input) of the agc loop can be programmed from -66dbm to -52dbm and is controlled by the pdet[2:0] bits in the pdet/rf-filt register (table 6). high-side and low-side lo injection the max2163 allows selection between high-side and low-side lo injection through the hsls bit in the mode register (table 7). to select low-side injection, set hsls to 1; to select high-side injection, set hsls to 0. if filter the nominal if filter center frequency and bandwidth are 571khz and 860khz, respectively. the center frequency of the if bandpass filter is tuned at the factory; however, the factory-set trim can be bypassed and the center frequency can be adjusted through the flts and tun[2:0] bits in the if filter reg- ister (table 3). set the flts bit to 0 to select the filter? center frequency to the factory-set tuning. set the flts bit to 1 to allow the filter? center frequency to be adjusted with the tun[2:0] bits (table 3). vco autoselect (vas) the max2163 includes three vcos with each vco hav- ing 16 sub-bands. the appropriate vco and vco sub- band for the desired local oscillator frequency can be manually selected by programming the vco[1:0] and vsb[3:0] bits in the vco register. the selected vco and sub-band is reported in the vas status register (read only) (table 13). alternatively, the max2163 can be set to autonomously choose a vco and vco sub-band. automatic vco selection is enabled by setting the vas bit in the vas register (table 4) and is initiated once the n-divider lsb register word is loaded. in the event that the r-divider is changed, both the r-divider msb and r-divider lsb registers must be reprogrammed. also, if the r-divider or the n-divider msb is changed, the n-divider lsb register must also be reprogrammed to initiate the vco autoselect function. the vco and vco sub-band that are programmed in the vco[1:0] and vsb[3:0] bits serve as the starting point for the automatic vco selection process when vass = 0. when vass = 1, the current vco and vco sub-bands serve as the start- ing point for the automatic vco selection process. during the selection process, the vase bit in the vas status register is cleared to indicate the autoselection function is active. upon successful completion, bits vase and vasa are set and the vco and sub-band selected are reported in the vas status register (table 13). if the search is unsuccessful, vasa is cleared and vase is set. this indicates that searching has ended, but no vco has been found, and occurs when trying to tune to a frequen- cy outside the vco? specified frequency range. charge-pump select (cps) the max2163 allows for manual selection of the charge-pump current (cps = 0) or automatic selection (cps = 1). when in manual mode, the charge-pump current is programmed by bits cp[1:0] in the r-divider lsb register (table 9). in automatic selection mode, the charge-pump current is automatically set based on vtune voltage and current vco sub-band. ade, adl, and vas bits must be programmed to 1. the selected charge-pump current is reported in table 18 . max2163 isdb-t 1-segment tuner 20 ______________________________________________________________________________________ vsb[3] adc[2] cp (ma) 0 0 2 0 1 3 1 0 1.5 1 1 2.5 table 18. charge-pump current setting when cps = 1
max2163 isdb-t 1-segment tuner ______________________________________________________________________________________ 21 3-bit analog-to-digital converter the max2163 includes a 3-bit adc. its input is con- nected to the vco tune pin (vtune). this adc can be used for checking the lock status of the vcos. table 19 summarizes the phase-locked loop (pll) lock status based on adc[2:0] values. the vco autoselect routine only selects a vco in the vas locked range. this allows room for a vco to drift over temperature and remain in a valid locked range. when vco autoselect is disabled, the adc must first be enabled by setting the ade bit in the vas register. the adc reading is latched by a subsequent programming of the adc latch bit (adl = 1). the adc value is reported in the status register (table 12). loop-time constant selection the loop-time constant (ltc) function sets the wait time for an adc read when in vco autoselect mode. this wait time determines how long the vco autoselect cir- cuit waits for the pll to settle before determining if vco selection was successful. the loop time constant is selectable by the ltc[1:0] bits in the vas register (table 4). xtalout buffer the reference buffer/divider is provided for driving external devices. the internal frequency divider is fixed at 2, and the buffer can provide a minimum 500mv p-p signal swing into a load of 4k ||10pf with a guaranteed duty cycle of 45% to 55%. upon power-up or coming out of shutdown, the xtalout buffer is held in shut- down for an additional 3ms (typ) by an internal timer circuit. this allows the crystal oscillator sufficient time to start up properly, without unwanted parasitic feedback from the output buffer. layout considerations the max2163 evaluation kit serves as a guide for pcb layout. keep rf signal lines as short as possible to mini- mize losses and radiation. use controlled impedance on all high-frequency traces. use abundant ground vias between rf traces to minimize undesired coupling. bypass each v cc_ pin to ground with a 0.1? capacitor placed as close as possible to the pin. when using the optional uhf tracking filter, keep the external inductor as close to the ic as possible and allow it to connect back to the top side ground as close as possible to the ic. to ensure proper crystal oscillator startup, place the crystal near the max2163 xtal pin (pin 21). the crys- tal ground should have a clear, short return back to the max2163 ground paddle near xtal. minimize the par- asitic capacitance between the board traces of xtal (pin 21) and xtalout (pin 22). refer to the max2163 evaluation kit data sheet for a recommended board layout. in addition, the ground returns for the vco, vtune, and charge pump require special layout consideration (see the typical application circuit ). the ldo capaci- tor (c66) and vccvco bypass capacitor (c17) grounds should be routed back to the max2163 ground paddle near pin 28. the loop filter ground con- nections of c27, c28, and c30 should be connected together before tapping down to the overall ground plane with a clear path back to pin 25 (gndsyn). when using the tqfn packaged device, the exposed paddle must be soldered evenly to the board? ground plane for proper operation. use abundant vias beneath the exposed paddle for maximum heat dissipation. adc[2:0] pll lock status 000 out of lock 001 locked 010 locked 011 not used 100 not used 101 locked 110 locked 111 unlocked table 19. pll and lock status
max2163 isdb-t 1-segment tuner 22 ______________________________________________________________________________________ chip information process: bicmos max2163 28 27 26 25 24 23 22 8 9 10 11 12 13 14 1 v cc 2 3 4 5 6 7 21 20 19 18 17 16 15 xtalout + pwrdet ifout tank div2 div pwrdet frequency synthesizer interface logic and control pwrdet lextu v cc v cc v cc uhfin v cc gc2 v cc scl sda v cc c19 c17 c66 r22 c30 c28 r20 c27 v cc typical application circuit package information for the latest package outline information and land patterns, go to www.maxim-ic.com/packages . package type package code document no. 28 tqfn-ep t2855-8 21-0140
max2163 isdb-t 1-segment tuner maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a maxim product. no circu it patent licenses are implied. maxim reserves the right to change the circuitry and specifications without notice at any time. maxim integrated products, 120 san gabriel drive, sunnyvale, ca 94086 408-737-7600 ____________________ 23 2009 maxim integrated products maxim is a registered trademark of maxim integrated products, inc. revision history revision number revision date description pages changed 0 7/08 initial release 1 4/09 updated to add 28-pin MAX2163ETI to data sheet all 2 10/09 added note instructing to program all registers; corrected register tables and listed all factory use only registers 10, 12, 14, 15, 16

▲Up To Search▲

Price & Availability of MAX2163ETI

	To Download MAX2163ETI Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .